Program Studi Mesin Industri 2026
Mahasiswa : Lodofikus Alfiano Deus, Muhammad Izdihar
Pembimbing : Shanti Kumbarasari M.T.
ABSTRAK/ABSTRACT
Tugas akhir ini membahas perancangan dan analisis sistem Slide Conveyor berbasis motor penggerak sebagai jalur output produk Work In Process (WIP) di PT Kimpai Dyna, perusahaan manufaktur kemasan tube. Penelitian ini dilatarbelakangi permasalahan pada jalur output mesin Body Making, yaitu penumpukan produk akibat sistem lengseran gravitasi yang tidak mampu mengimbangi kecepatan keluaran mesin sebesar 120 produk/menit. Penelitian bertujuan merancang sistem pemindah produk yang mengontrol aliran WIP secara stabil dan sinkron dengan laju mesin, serta memastikan kekuatan rangka aman untuk operasional. Metode meliputi identifikasi masalah melalui observasi, pemilihan konsep dengan matriks morfologi, dan perhitungan mekanik untuk menentukan spesifikasi penggerak. Hasil perancangan menetapkan motor AC 1 fasa tipe geared motor, rangka besi hollow 50×50 mm dan 40×40 mm, pulley 60 mm, serta poros 30 mm dengan bearing UCP 204, menghasilkan kecepatan linear 0,4 m/s. Simulasi menunjukkan displacement maksimum hanya 0,04644 mm sehingga rangka dinyatakan sangat aman. Pengujian pada 100 sampel tube membuktikan sistem ini memperlancar aliran produk, menstabilkan waktu proses, dan menekan penumpukan WIP secara signifikan.
Kata Kunci : Slide Conveyor, O-Ring Round Belt, Work In Process (WIP),
This final project addresses the design and analysis of a motor-driven Slide Conveyor system as the output pathway for Work In Process (WIP) products at PT Kimpai Dyna, a tube-packaging manufacturer. The study is motivated by a problem at the output line of the Body Making machine, where a gravity-based slide chute failed to keep pace with an output speed of 120 products per minute, causing product pile-up. This research aims to design a product-transfer system that controls WIP flow stably and in sync with the machine rate, while keeping the frame structurally safe. The method includes problem identification through observation, concept selection using a morphological matrix, and mechanical calculations to determine drive specifications. The design specifies a single-phase AC geared motor, a 50×50 mm and 40×40 mm hollow-iron frame, a 60 mm pulley, and a 30 mm shaft with UCP 204 bearings, producing a linear speed of 0.4 m/s. Simulation shows a maximum displacement of only 0.04644 mm, confirming the frame is safe. Testing on 100 tube samples proved the system smooths product flow, stabilizes process time, and reduces WIP pile-up.
Keywords : Slide Conveyor, O-Ring Round Belt, Work In Process (WIP), Drive
DAFTAR PUSTAKA
Arfandi, A., & Supit, Y., “Prototipe Sistem Otomasi pada Pengisian Depot Air Minum Isi Ulang Berbasis Arduino Uno,” Jurnal Sistem Informasi dan Teknik Komputer, vol. 4, no. 1, hal. 91, 2019.
Kurniawan, M. S., Wijaya, K., & Purba, H. H., “Implementasi Sistem Kendali Otomatis Pada Industri Manufaktur: Kajian Literatur,” Teknoin, vol. 30, no. 1, hal. 1–8, 2025.
Widi et al “Analisis Dampak Otomasi Industri terhadap Efisiensi Operasional dan Optimasi Konsumsi Energi,” Jurnal Ilmiah Teknologi dan Rekayasa,
A. Kusnandar, “Revolusi Industri 1.0 hingga 4.0”. Bandar Lampung: Umitra,
Kasnawati, Sampe, R., Kusdiah, Y., & Sriwati, M., “Pengembangan Teknologi Mesin Otomatis untuk Peningkatan Produktivitas dalam Industri Manufaktur,” Jurnal Review Pendidikan dan Pengajaran, vol. 7, no. 4, hal. 15300–15301, 2024.
H. Alfarizi, A. H. Anshor, dan Edora, “Sistem Informasi WIP (Work In Process) Berbasis Web Menggunakan Metode Waterfall,” KLIK: Kajian Ilmiah Informatika dan Komputer, vol. 4, no. 3, hal. 1483-1492, 2023.
Rachael, A., “Minimasi Work In Process pada Produksi Kantung Plastik dengan Theory of Constraints di PT Flamboyan Jaya,” Skripsi S.T., Program Studi Teknik Industri, Fakultas Teknik, Universitas Brawijaya, Malang,
M. Andrejiova et al, “Measurement and Determination of the Absorbed Impact Energy for Conveyor Belts of Various Structures under Impact Loading,” Measurement, vol. 131, hal. 362-371, 20. 71 72
Shanti Kumbarasari, “Otomatisasi Pengisian Runner Plastik Polyethylene dengan Autolader Conveyor” Jurnal Simetris, vol. 18, hal. 24-25, 2024.
S. Hariyadi dan D. Kurniawan, “Perencanaan Belt Conveyor System Sebagai Alat Angkut Box Kapasitas 36 ton/jam dengan Panjang Horisontal 18 m di PT. Karunia Alam Segar,” Wahana Teknik, vol. 8, no. 1, hal. 49-61, 2019.